8" Round White Pine Vertical Log Corner Post - Pie Cut

Prices are listed per linear foot.
SKU
WPVLCPPCO
$17.95

Have questions about this product?
Call us at 800-299-8981.

White Pine Vertical Log Corner Posts - Pie Cut Only Specifications:
Available Dimensions: 8" Round
Available Lengths: 12' lengths in stock. 8' and 10' lengths available via special order.
Drying Type: Air-Dried
Profile: "Pie Cut" Round Profile.
Texture: Milled Smooth.
Preferred Fasteners: Stainless Steel Screws or Nails.
Typical Weight per board foot: 3 lbs./bf
Shipping Options: Flat-bed tractor trailer, Roll Back, LTL Carrier. Shipping method is determined based on location and order size to minimize cost.
**When shipping via LTL carrier, pallets longer than 12' are subject to a $150 fee by the carrier for Overlength Freight.**
Please Note: The product images shown are for illustration purposes only and may not be an exact representation of the product. Twin Creeks reserves the right to change product specifications at any time without notice.

White Pine Log Corner Features and Benefits:
• Compatible for interior and exterior applications.
• Features a full-round "pie-cut" profile suitable for use with sheetrock, shiplap siding, as well as traditional log siding
• Air-Dried for reliable stability and exceptional stain acceptance.

White Pine Log Corners Preparation Information:
Our White Pine Vertical Log Corners are ready for installation once received on your jobsite. However, wood will shrink and swell with changes in moisture content and weather. According to NeLMA, to minimize dimensional change after installation, install white pine at a moisture content that matches with local climate as closely as possible. If climate in a particular region causes wood to maintain 8% to 13% moisture content annually, then the most ideal white pine would be installed at a moisture content within that range, and the material would be stored, stickered and protected for a week to ten days prior to application.

Preparing Vertical Log Corners for Staining
Proper preparation of your white pine lumber product before staining, as well as the staining procedure itself, can ensure that your finished product exceeds expectations. Below are a few valuable tips for the proper preparation of the wood and application of wood staining products.

  • Prepare the Vertical Log Corner: Use a TSP (Tri Sodium Phosphate) and Bleach wash to open up the cellular structure of the wood so the stain will penetrate further into the grain. Please refer to the manufacturer of the stain that you choose for further cleaning and preparation information.

  • Stain quality: There is a wide range of products and, of course, the best products can be the most expensive. Even a quality stain will not wear well if preparation is inadequate or sun exposure is excessive. Look for guarantees and for stain life expectancies as published by the manufacturer. Follow all manufacturers’ recommendations for product preparation and stain application.

  • Stain application: Unlike paint, stain is designed to soak into the wood. Two healthy coats of stain back-brushed into the wood itself are much better than one heavy coat of stain that will sit on the surface. If you apply your stain like a thick coat of paint, the stain will ultimately chip, crack and peel.

  • Color choice: The predominant enemy of stain is the UV rays of the sun. Lighter stain colors will fail faster than darker stain colors because UV rays penetrate further into the lighter colored product.

  • Limit sun exposure: If you are still designing your home, you might want to position your home in relation to the sun in order to minimize sun exposure. It is always good idea to have an 18-24 inch overhanging soffit on your roof to keep your log coners out of the sun as much as possible.

Storage of White Pine Vertical Log Corner Prior To Application:
Until installed, all white pine needs protection from direct sunlight, water saturation, snow, ice, dirt, and other elements. It is best to store white pine flat and off the ground with a vapor barrier so that moisture is not absorbed from the ground or from either side of the corner. White Pine should be protected with a waterproof covering elevated in the center so that water does not pool on the cover. We also recommend that you do not completely seal the product, as good air circulation is required to prevent any blue stain or molding. Ideally, the corners should be stored in an enclosed building such as a garage prior to use.

More Information
SpeciesEastern White Pine
We found other products you might like!