White Pine Saddle Notch False Corners

Saddle Notch False Corners are designed to deliver the appeal of traditional whole log construction while actually using log siding. Milled from Eastern White Pine, our Saddle Notch false corners provide the distinction and durability of a traditional log home.
Starting at $62.95

Have questions about this product?
Call us at 800-299-8981.

White Pine Saddle Notch False Corner Specifications:
Available Lengths: 3' and 4' pieces.
Typical Lead Time: Please call for an expected lead time as production schedules for this product may vary with seasonality.
Drying Type: Air Dried.
Texture: Milled Smooth.
Fastener Type: Stainless Steel Fastener.
Hewing Options: Draw Knifing is available on this profile for an additional $1.50/lf per side.
Shipping Options: Flat-bed tractor trailer, Roll Back, LTL Carrier. Shipping method is determined based on location and order size to minimize cost.
Additional Products Recommended for Installation: A good quality caulk such as Perma Chink Woodsman Caulk or Weatherall UV Guard Textured Caulk. You can find our selection of caulks at our Caulk page. Before applying a stain, it is also recommended to apply a Borate solution such as Armor Guard to the bare wood before staining to help prevent mold, mildew or termites.
Please Note: The product images shown are for illustration purposes only and may not be an exact representation of the product. Twin Creeks reserves the right to change product specifications at any time without notice.

White Pine Saddle Notch False Corner Coverage Calculations:
• Log siding using the Saddle Notch false corners need to be installed with a half course of "starter" siding to accomodate for the need to partially offset the siding courses on the different sides of the corner. Please refer to photos for an illustration.
• Saddle Notch false corners use 1 piece for each side of an outside corner.
• Example: 2x8 Siding with Saddle Notch False Corners, 8' wall height. You will typically need 14 runs of 8” log siding to cover an 8' wall height (8'*12"= 96". 96"/7" coverage per board = 14 runs needed). Given that you need a Saddle Notch false corner piece for each side of the wall corner on each run of siding, you will need 28 saddle notch false corner pieces (14 runs * 2 sides).
• Please call us if you would like a free takeoff for your project as well.

Matching Siding Profiles:

6x8 "D" Saddle Notch False Corners
• Matching Log Siding: 2x8 White Pine "D" Log Siding (Deep Profile)
• Stack Height: 7 1/4"
• Typical Corner Overhang Length: 6"
• Log End Width: 5 1/2"

8x8 "D" Saddle Notch False Corners
• Matching Log Siding: 2x8 White Pine "D" Log Siding (Deep Profile)
• Stack Height: 7 1/4"
• Typical Corner Overhang Length: 8"
• Log End Width: 7 1/4"

6x10 "D" Saddle Notch False Corners
• Matching Log Siding: 3x10 White Pine "D" Log Siding
• Stack Height: 9 1/4"
• Typical Corner Overhang Length: 6"
• Log End Width: 5 1/2"

Storage Prior To Installation:
Until installed, False Corners need protection from direct sunlight, water saturation, snow, ice, dirt, and other elements. It is best to store the corners flat and off the ground with a vapor barrier so that moisture is not absorbed through the bottom boards of the stack. The lumber should be protected with a waterproof covering elevated in the center so that water does not pool on the cover. We also recommend that you do not completely seal the bundle, as good air circulation is required to prevent any blue stain or molding. Ideally, the corners should be stored in an enclosed building such as a garage prior to use.

How to Install Saddle Notch False Corners:

Left and Right Corners- When installing Saddle Notch false corners, it is important to become familiar with the “left” and “right” corner pieces. The left false corner will feature the siding continuing beyond the "log tail" on the left side and the right corner will feature the siding continuing beyond the "log tail" on the right side.

Starter and End-Cap Corner Pieces- Saddle Notch false corners are designed to be built beginning with a "starter corner" and to end with an "end cap corner". These will be included in your order but they will look different than the rest of your false corners. The starter false corner will be milled to look like the top half of your Saddle Notch false corners and the end cap false corner will be milled to look like the bottom half of your Saddle Notch false corners.

Starting Saddle Notch False Corners:
1. Start by confirming on which side of the house you had planned to use the starter pieces of log siding. Typically, this will be the short side of the house. Your first step then will be to install a Saddle Notch false corner starter piece at either of this side’s house corners.
2. Once you have the starter Saddle Notch false log corner down, continue your log siding across the side you have started on.
3. For the alternate side of the corner from your starter piece, use full false log corners from the beginning to the end. For the log siding, you may need to notch out a ½” groove to carry the log siding on below the main level. This will allow you to cover the sub-floor band if needed.

Fastening False Corners and Siding:
1. Fasten the corner to the wall by toe-screwing at both the top of the log tail and the top of the siding portion to ensure a secure fit.
2. Install your first run of log siding by matching it against the end of your false corner siding portion, fastening the first run of siding on both the top and bottom edges of the board.
3. Fasten your first run of log siding on the opposite side of the wall to butt up directly behind the log tail of your false corner.
4. The next false corner will then be placed to match its “groove” with the previous row’s log siding “tongue” crossing over the previous false corner at a 90 degree angle. After the corner is in place, fasten the corner to the wall at the top of both the siding portion, and log tail of the false corner.
5. Fasten your next row of log siding to butt against the back end of the false corner log tail you just installed to complete your second row of corners.
6. Repeat this process until you have reached the eve of your wall and your corner is completed.

Finishing Saddle Notch False Corners:
1. For the last section of the framed wall that used a starter corner, use the end cap of a Saddle Notch false corner to cap off the false corner section on this side of the corner.
2. On the last section of the wall that used a full Saddle Notch false corner, use another full Saddle Notch false corner to finish it.

Additional Tips:
• False Corner siding tails should be "staggered" in order to break up the joint line created by matching the log siding against the siding tails. This can be done by trimming the siding tail ends to random lengths, or purchasing varied lengths.
• Log siding is installed as the false corners are installed and each course should be checked that it is level before moving on to the next course.
• When fastening the false corners and log siding, fasteners should be driven flush to ensure a proper fit between the materials.

As with every unfinished exterior wood, applying a quality finish to all surfaces (including the ends) is recommended. An exterior finish protects the wood from moisture absorption and UV degradation, and helps prevent staining caused by mold and mildew. Before applying a finish to the wood, it is best to confirm that there is no mill glaze present on the wood. Mill glaze can inhibit or interfere with the finish treatment and is produced when the material is manufactured through the planer. When mill glaze occurs, it is recommended to remove it by pressure washing the wood or sanding prior to staining. Sanding is not recommended as a first option unless every piece is sanded. We offer a wide selection of Oil and Water Based exterior finishes that we can recommend based on the final finish, maintenance schedule and look that is desired. Most exterior finishes do have to be re-coated or reapplied every 3 -5 years depending on the UV exposure to your home. You can find all of the exterior stain products that we carry at our Exterior Stains page.

More Information
SpeciesEastern White Pine
We found other products you might like!