2x6 White Pine Tongue and Groove Decking Features and Benefits:
• Quick and Easy Installation. ~ Great for Do-It-Yourself or weekend projects.
• Precision Milled, Solid Wood Tongue and Groove.
• Flexibility and Versatility ~ Tongue and Groove can be Installed to any Existing Home or Building.
• Kiln Dried ~ Low Moisture Content to prevent shrinkage and swelling.
• Reversible Smooth Surface ~ Ready to install and finish with final stain or clear coat.
• Stack Height: 5"
• Thickness: 1 1/2 "
• Available Lengths: 8', 10’, 12’, 14’, and 16'. Specified piece counts are available depending on current stock at time of order.
• Minimum Order Quantity: This profile is available as a special order. The manufacturer requires an order minimum of 1000 lf to produce this profile.
• Typical Lead Time: Typically available in 2-3 weeks.
• Grade: NeLMA Standard Grade.
• Installation Type: Stainless Steel Nail or Screw.
• Cutting Waste: Recommended approximately 5%-10% for walls, 15%-25% for gable ends depending on roof angle.
• Typical Weight per linear foot: 1 ½ lbs./lf
• Profile: Milled Smooth.
• Hewing Option: Hand Hewing or Draw Knifing is not available on this profile.
• Shipping Options: Flat-bed tractor trailer, Roll Back, LTL Carrier. Shipping method is determined based on location and order size to minimize cost.
**When shipping via LTL carrier, pallets longer than 12' are subject to a $150 fee by the carrier for Overlength Freight.**
• Please Note: The product images shown are for illustration purposes only and may not be an exact representation of the product. Twin Creeks reserves the right to change product specifications at any time without notice.
You can calculate the coverage for the tongue and groove using our Tips page: How Do I Determine How Much Lumber I Need? Please call us if you would like a free takeoff for your project as well.
Our Kiln Dried 2x6 White Pine Tongue and Groove Decking is ready for installation once received on your jobsite. However, wood will shrink and swell with any changes in moisture content and weather. According to NeLMA, to minimize dimensional change after installation, install tongue and groove at a moisture content that matches with local climate as closely as possible. If climate in a particular region causes wood to maintain 8% to 13% moisture content annually, then the most ideal tongue and groove would be installed at a moisture content within that range, and the material would be stored, stickered and protected for a week to ten days prior to application.
With any unfinished interior wood, applying a quality finish to all surfaces (including the ends) is recommended. An interior finish protects the wood from moisture absorption and UV degradation, and helps prevent any finger stains caused by touching the unfinished wood. On occasion, the tongue and groove may have a mill glaze that is produced when the material is manufactured through the planer. When mill glaze occurs, it is recommended to remove it by sanding prior to staining or clear coating the wood. Sanding is not recommended as a first option unless every piece is sanded. We offer a wide selection of Water Based Interior Finishes that we can recommend based on the final sheen level and look that is desired. Most interior finishes do not have to be re-coated or reapplied depending on the UV exposure to your home. You can find all of the interior stains and finish products that we carry at our https://www.twincreeksloghomes.com/interior-stains.html.
Storage Prior To Application:
Until installed, all tongue and groove needs protection from direct sunlight, water saturation, snow, ice, dirt, and other elements. Ideally, the tongue and groove should be stored in an enclosed building such as a garage prior to use. It is best to store the tongue and groove flat and off the ground with a vapor barrier so that moisture is not absorbed through the bottom boards of the stack. If stored outside, the siding should be protected with a waterproof covering elevated in the center so that water does not pool on the cover. We also recommend that you do not completely seal the bundle, as good air circulation is required to prevent any blue stain or molding.
It sounds like you're looking for a tongue & groove board that is square edged on both the top and bottom faces. While I don't have a board that fits that exactly, both our 2x6 White Pine and 2x6 Spruce tongue & groove boards are square edged on the top face and V-grooved on the bottom face. That may fit what you're looking for. We can provide a profile sheet of any of these boards if you'd like as well. Please let us know if we can help!