1x6 Western Red Cedar Tongue & Groove Paneling

Prices are Listed Per Linear Foot (lf).
SKU:
$2.09

1x6 Western Red Cedar Tongue and Groove Paneling Specifications:
• Stack Height: 5"
• Thickness: 3/4"
• Available Lengths: 8', 10’, 12’, 14’, and 16'. Specified piece counts are available depending on current stock at time of order.
• Grade: STK Grade (Select Tight Knotty).
• Cutting Waste: Recommended approximately 5%-10% for walls, 15%-25% for gable ends depending on roof angle.
• Typical Weight per linear foot: 1/2 lb./lf
• Profile: (1) Side – Rough Texture, (1) Side - Milled Smooth.
**Please note: Even though the 1x6 T&G board is reversible, it is graded to the rough side.**
• Hewing Option: Hand Hewing or Draw Knifing is not available on this profile.
• Shipping Options: Flat-bed tractor trailer, Roll Back, LTL Carrier. Shipping method is determined based on location and order size to minimize cost.
Details Disclaimer: While we strive to ensure product details are always accurate, product specifications may change and images shown may not represent current dimensions. Please call us if you would like to receive an up-to-date profile drawing.

Product Resources:
How To Install Western Red Cedar Siding
Quick Facts About Western Red Cedar
8 Reasons Why Western Red Cedar Is The Right Choice For Your Home
How to Finish Western Red Cedar
How to Specify Western Red Cedar



Coverage Calculations:
You can calculate the coverage for the tongue and groove using our Tips page: How Do I Determine How Much Lumber I Need? Please call us if you would like a free takeoff for your project as well.

Preparation Information:
Our Kiln Dried 1X6 Western Red Cedar Tongue and Groove paneling is ready for installation once received on your jobsite. However, wood will shrink and swell with any changes in moisture content and weather. According to WRCLA, to minimize dimensional change after installation, install tongue and groove at a moisture content that matches with local climate as closely as possible. If climate in a particular region causes wood to maintain 8% to 13% moisture content annually, then the most ideal tongue and groove would be installed at a moisture content within that range, and the material would be stored, stickered and protected for a week to ten days prior to application.

Paneling Maintenance:
With any unfinished interior wood, applying a quality finish to all surfaces (including the ends) is recommended. An interior finish protects the wood from moisture absorption and UV degradation, and helps prevent any finger stains caused by touching the unfinished wood. On occasion, the tongue and groove may have a mill glaze that is produced when the material is manufactured through the planer. When mill glaze occurs, it is recommended to remove it by sanding prior to staining or clear coating the wood. Sanding is not recommended as a first option unless every piece is sanded. We offer a wide selection of Water Based Interior Finishes that we can recommend based on the final sheen level and look that is desired. Most interior finishes do not have to be re-coated or reapplied depending on the UV exposure to your home. You can find all of the interior stains and finish products that we carry at our Interior Stains page.

Storage Prior To Application:
Until installed, all tongue and groove needs protection from direct sunlight, water saturation, snow, ice, dirt, and other elements. Ideally, the tongue and groove should be stored in an enclosed building such as a garage prior to use. It is best to store the tongue and groove flat and off the ground with a vapor barrier so that moisture is not absorbed through the bottom boards of the stack. If stored outside, the siding should be protected with a waterproof covering elevated in the center so that water does not pool on the cover. We also recommend that you do not completely seal the bundle, as good air circulation is required to prevent any blue stain or molding.

Product Questions

Have a Question?

Be the first to ask a question about this.

Ask a Question
DETAILS

1x6 Western Red Cedar Tongue and Groove Paneling Specifications:
• Stack Height: 5"
• Thickness: 3/4"
• Available Lengths: 8', 10’, 12’, 14’, and 16'. Specified piece counts are available depending on current stock at time of order.
• Grade: STK Grade (Select Tight Knotty).
• Cutting Waste: Recommended approximately 5%-10% for walls, 15%-25% for gable ends depending on roof angle.
• Typical Weight per linear foot: 1/2 lb./lf
• Profile: (1) Side – Rough Texture, (1) Side - Milled Smooth.
**Please note: Even though the 1x6 T&G board is reversible, it is graded to the rough side.**
• Hewing Option: Hand Hewing or Draw Knifing is not available on this profile.
• Shipping Options: Flat-bed tractor trailer, Roll Back, LTL Carrier. Shipping method is determined based on location and order size to minimize cost.
Details Disclaimer: While we strive to ensure product details are always accurate, product specifications may change and images shown may not represent current dimensions. Please call us if you would like to receive an up-to-date profile drawing.

Product Resources:
How To Install Western Red Cedar Siding
Quick Facts About Western Red Cedar
8 Reasons Why Western Red Cedar Is The Right Choice For Your Home
How to Finish Western Red Cedar
How to Specify Western Red Cedar



Coverage Calculations:
You can calculate the coverage for the tongue and groove using our Tips page: How Do I Determine How Much Lumber I Need? Please call us if you would like a free takeoff for your project as well.

Preparation Information:
Our Kiln Dried 1X6 Western Red Cedar Tongue and Groove paneling is ready for installation once received on your jobsite. However, wood will shrink and swell with any changes in moisture content and weather. According to WRCLA, to minimize dimensional change after installation, install tongue and groove at a moisture content that matches with local climate as closely as possible. If climate in a particular region causes wood to maintain 8% to 13% moisture content annually, then the most ideal tongue and groove would be installed at a moisture content within that range, and the material would be stored, stickered and protected for a week to ten days prior to application.

Paneling Maintenance:
With any unfinished interior wood, applying a quality finish to all surfaces (including the ends) is recommended. An interior finish protects the wood from moisture absorption and UV degradation, and helps prevent any finger stains caused by touching the unfinished wood. On occasion, the tongue and groove may have a mill glaze that is produced when the material is manufactured through the planer. When mill glaze occurs, it is recommended to remove it by sanding prior to staining or clear coating the wood. Sanding is not recommended as a first option unless every piece is sanded. We offer a wide selection of Water Based Interior Finishes that we can recommend based on the final sheen level and look that is desired. Most interior finishes do not have to be re-coated or reapplied depending on the UV exposure to your home. You can find all of the interior stains and finish products that we carry at our Interior Stains page.

Storage Prior To Application:
Until installed, all tongue and groove needs protection from direct sunlight, water saturation, snow, ice, dirt, and other elements. Ideally, the tongue and groove should be stored in an enclosed building such as a garage prior to use. It is best to store the tongue and groove flat and off the ground with a vapor barrier so that moisture is not absorbed through the bottom boards of the stack. If stored outside, the siding should be protected with a waterproof covering elevated in the center so that water does not pool on the cover. We also recommend that you do not completely seal the bundle, as good air circulation is required to prevent any blue stain or molding.

MORE INFORMATION
REVIEWS
PRODUCT QUESTIONS

Product Questions

Have a Question?

Be the first to ask a question about this.

Ask a Question